For media inquiries, please visit wdwnews.com. Panelists have received/will receive a Walt Disney World® Resort, Disneyland® Resort or Disney Cruise Line® vacation for panelist and up to three family members and/or park tickets for their planDisney panel participation. By default, the Navigation pane doesn’t show the Libraries in Windows 10, as it did in Windows 7. Fortunately, the libraries aren’t gone; they’re just hidden. To enable and use the libraries in Windows 10, open File Explorer and follow these steps: In the File Explorer.
Important
Welcome to Microsoft Defender for Endpoint, the new name for Microsoft Defender Advanced Threat Protection. Read more about this and other updates here. We'll be updating names in products and in the docs in the near future.
Applies to:
Want to experience Microsoft Defender ATP? Sign up for a free trial.
Supported client operating systems
Based on the version of Configuration Manager you're running, the following client operating systems can be onboarded:
Configuration Manager version 1910 and prior
Configuration Manager version 2002 and later
Starting in Configuration Manager version 2002, you can onboard the following operating systems:
Onboard devices using System Center Configuration Manager
Check out the PDF or Visio to see the various paths in deploying Microsoft Defender ATP.
Note
Microsoft Defender ATP doesn't support onboarding during the Out-Of-Box Experience (OOBE) phase. Make sure users complete OOBE after running Windows installation or upgrading.
Tip
After onboarding the device, you can choose to run a detection test to verify that an device is properly onboarded to the service. For more information, see Run a detection test on a newly onboarded Microsoft Defender ATP device.
Note that it is possible to create a detection rule on a Configuration Manager application to continuously check if a device has been onboarded. An application is a different type of object than a package and program.If a device is not yet onboarded (due to pending OOBE completion or any other reason), Configuration Manager will retry to onboard the device until the rule detects the status change.
![]()
This behavior can be accomplished by creating a detection rule checking if the 'OnboardingState' registry value (of type REG_DWORD) = 1.This registry value is located under 'HKLMSOFTWAREMicrosoftWindows Advanced Threat ProtectionStatus'.For more information, see Configure Detection Methods in System Center 2012 R2 Configuration Manager.
Configure sample collection settings
For each device, you can set a configuration value to state whether samples can be collected from the device when a request is made through Microsoft Defender Security Center to submit a file for deep analysis.
Note
These configuration settings are typically done through Configuration Manager.
You can set a compliance rule for configuration item in Configuration Manager to change the sample share setting on a device.
This rule should be a remediating compliance rule configuration item that sets the value of a registry key on targeted devices to make sure they’re complaint.
The configuration is set through the following registry key entry:
Where:
Key type is a D-WORD. Possible values are: File Pane 1 10 7 Mm =
The default value in case the registry key doesn’t exist is 1.
For more information about System Center Configuration Manager Compliance, see Introduction to compliance settings in System Center 2012 R2 Configuration Manager.
Other recommended configuration settings
After onboarding devices to the service, it's important to take advantage of the included threat protection capabilities by enabling them with the following recommended configuration settings.
Device collection configuration
If you're using Endpoint Configuration Manager, version 2002 or later, you can choose to broaden the deployment to include servers or down-level clients.
Next generation protection configuration
The following configuration settings are recommended:
Scan
Real-time Protection
Cloud Protection Service
Attack surface reductionConfigure all available rules to Audit.
Note
Blocking these activities may interrupt legitimate business processes. The best approach is setting everything to audit, identifying which ones are safe to turn on, and then enabling those settings on endpoints which do not have false positive detections.
Network protection
Prior to enabling network protection in audit or block mode, ensure that you've installed the antimalware platform update, which can be obtained from the support page.
Controlled folder access
Enable the feature in audit mode for at least 30 days. After this period, review detections and create a list of applications that are allowed to write to protected directories.
For more information, see Evaluate controlled folder access.
Offboard devices using Configuration Manager
For security reasons, the package used to Offboard devices will expire 30 days after the date it was downloaded. Expired offboarding packages sent to a device will be rejected. When downloading an offboarding package, you will be notified of the packages expiry date and it will also be included in the package name.
Note
Onboarding and offboarding policies must not be deployed on the same device at the same time, otherwise this will cause unpredictable collisions.
Offboard devices using Microsoft Endpoint Configuration Manager current branch
If you use Microsoft Endpoint Configuration Manager current branch, see Create an offboarding configuration file.
Offboard devices using System Center 2012 R2 Configuration Manager
Important
Offboarding causes the device to stop sending sensor data to the portal but data from the device, including reference to any alerts it has had will be retained for up to 6 months.
Monitor device configuration
If you're using Microsoft Endpoint Configuration Manager current branch, use the built-in Microsoft Defender ATP dashboard in the Configuration Manager console. For more information, see Microsoft Defender Advanced Threat Protection - Monitor.
If you're using System Center 2012 R2 Configuration Manager, monitoring consists of two parts:
Confirm the configuration package has been correctly deployed
Check that the devices are compliant with the Microsoft Defender ATP service
You can set a compliance rule for configuration item in System Center 2012 R2 Configuration Manager to monitor your deployment.
This rule should be a non-remediating compliance rule configuration item that monitors the value of a registry key on targeted devices.
Monitor the following registry key entry:
For more information, see Introduction to compliance settings in System Center 2012 R2 Configuration Manager.
Related topics-->
Answer files (or Unattend files) can be used to modify Windows settings in your images during Setup. You can also create settings that trigger scripts in your images that run after the first user creates their account and picks their default language.
Windows Setup will automatically search for answer files in certain locations, or you can specify an unattend file to use by using the
/unattend: option when running Windows Setup (setup.exe).
Windows settings overview
While you can set many Windows settings in audit mode, some settings can only be set by using an answer file or Windows Configuration Designer, such as adding manufacturer’s support information. A full list of answer file settings (also known as Unattend settings) is in the Unattended Windows Setup Reference.
Enterprises can control other settings by using Group Policy. For more info, see Group Policy.
Answer file settings
You can specify which configuration pass to add new settings:
Note
These settings could be lost if the user resets their PC with the built-in recovery tools. To see how to make sure these settings stay on the device during a reset, see Sample scripts: Keeping Windows settings through a recovery.
Create and modify an answer fileFile Pane 1 10 7 Mm InchesStep 1: Create a catalog file
Step 2: Create an answer file
Step 3: Add new answer file settings
See the Unattended Windows Setup Reference for a full list of configuration options.
File Pane 1 10 7 Mm Equals
Step 4: Save the answer file
Since we specified a script to run in Step 3, let's create that script now.
Add the answer file and script to the imageStep 6: Mount an image and add the answer fileFile Pane 1 10 7 Mm Socket
When you apply your image, Windows will process your unattend file and will configure your settings based on what you specified in the unattend.
Comments are closed.
|
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |